Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WG6 BGVW BK00564 - PA6-GF30 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Mechanical properties - Thermal properties - Electrical properties - Other properties - Material specific properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

Glass fibre reinforced and heat ageing resistant injection moulding grade used e.g. for automobile manifolds

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	9600 / 5600	MPa	ISO 527
Stress at break	180 / 90	MPa	ISO 527
Strain at break	3 / 6	%	ISO 527
Charpy impact strength, +23°C	80 / 80	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	65 / -	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	12 / 20	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	9 / -	kJ/m²	ISO 179/1eA

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	220 / *	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	205 / *	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	218 / *	°C	ISO 75-1/-2
Coeff. of linear therm. expansion, parallel	18.4 / *	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion, normal	96.4 / *	E-6/K	ISO 11359-1/-2
Burning Behav. at 1.5 mm nom. thickn.	HB / *	class	IEC 60695-11-10

Electrical properties	dry / cond	Unit	Test Standard
ISO Data
Electric strength	40 / 31	kV/mm	IEC 60243-1

Other properties	dry / cond	Unit	Test Standard
Water absorption	6.6 / *	%	Sim. to ISO 62
Humidity absorption	2.1 / *	%	Sim. to ISO 62
Density	1360 / -	kg/m³	ISO 1183

Material specific properties	dry / cond	Unit	Test Standard
ISO Data
Viscosity number	142 / *	cm³/g	ISO 307, 1157, 1628

Diagrams

Characteristics

Processing

Injection Molding

Delivery form

Black

Regional Availability

North America, Europe, Asia Pacific

Other text information

Injection molding

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 270 - 290 °C
injection molding, Melt temperature, recommended: 280 °C
injection molding, Mold temperature, range: 80 - 90 °C
injection molding, Mold temperature, recommended: 80 °C
injection molding, Dwell time, thermoplastics: 10 min

Chemical Media Resistance

Acids
	Acetic Acid (5% by mass) (23°C)
	Citric Acid solution (10% by mass) (23°C)
	Lactic Acid (10% by mass) (23°C)
	Hydrochloric Acid (36% by mass) (23°C)
	Nitric Acid (40% by mass) (23°C)
	Sulfuric Acid (38% by mass) (23°C)
	Sulfuric Acid (5% by mass) (23°C)
	Chromic Acid solution (40% by mass) (23°C)
Bases
	Sodium Hydroxide solution (35% by mass) (23°C)
	Sodium Hydroxide solution (1% by mass) (23°C)
Alcohols
	Isopropyl alcohol (23°C)
	Methanol (23°C)
	Ethanol (23°C)
Hydrocarbons
	n-Hexane (23°C)
	Toluene (23°C)
	iso-Octane (23°C)
Ketones
	Acetone (23°C)
Ethers
	Diethyl ether (23°C)
Mineral oils
	SAE 10W40 multigrade motor oil (23°C)
	SAE 10W40 multigrade motor oil (130°C)
Standard Fuels
	Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
	Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
	Sodium Chloride solution (10% by mass) (23°C)
	Sodium Hypochlorite solution (10% by mass) (23°C)
	Zinc Chloride solution (50% by mass) (23°C)
Other
	Ethyl Acetate (23°C)
	Hydrogen peroxide (23°C)
	DOT No. 4 Brake fluid (130°C)
	Ethylene Glycol (50% by mass) in water (108°C)
	Water (23°C)

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.